System settings: network, display and sound on the Controller
The System tab on the LemonScore Controller sets up Wi-Fi or Ethernet, screens, keyboard, sound and time, and shows temperatures and a connection test.
The System tab only exists on the LemonScore Controller. This is where you set up the device itself: network, screens, sound, the clock and more. Open it under Settings › System. Pick an area on the left; its settings appear on the right.
Network
The Controller is connected either by cable (Ethernet) or by Wi-Fi, never both at once. Under Connection type you see which connection is active and the Controller's IP address.
Connect to a Wi-Fi network
- Tap Wi-Fi under Connection type.
- Answer Switch to Wi-Fi? with Confirm. The wired connection is switched off.
- Tap your network in the Wi-Fi networks list. Networks with a padlock need a password.
- Enter the password and tap Connect.
If the password is wrong, the dialog stays open and shows an error. Tap the connected network to see its signal and IP address. There you can end the connection with Disconnect or delete the saved network with Forget.
When you change the connection type, the scoreboard and any connected remotes lose the network for a moment and may get a different IP address. Don't switch during a match.
Set a fixed IP address
The Controller normally gets its address automatically. If your network needs a fixed address:
- Tap Manual under Address assignment.
- Fill in IP address, Subnet prefix, Gateway and DNS.
- Tap Apply and confirm Apply IP settings?.
Automatic (DHCP) switches back to an automatic address.
Test the connection
At the bottom, under Connection test, tap Run test. LemonScore checks Network link, Name resolution (DNS), Internet and Licensing server in turn. A green tick means the step is fine; a red cross shows where the problem is.
Display
Here you set up the connected screens, for example the touchscreen and the cable to the LED wall or TV.
- If several screens are connected, choose one under Display. The switch in the row below turns it on or off.
- Under Resolution & orientation, choose the Resolution, the Scale and the Orientation (for example Landscape or Portrait (left)).
- If several screens are active, drag them in the preview at the top so they match how the screens are placed. They snap together at the edges.
- Tap Apply and confirm with Confirm.
While the settings are applied, the screen may flicker or go black for a moment.
Keyboard
Under Keyboard you choose the key layout, for example German (Switzerland). It applies straight away, both to a connected keyboard and to the on-screen keyboard. With German (Switzerland), the on-screen keyboard shows the Swiss German layout with è, é and à, see Use the on-screen keyboard. Show on-screen keyboard switches the on-screen keyboard off if you work with a real keyboard.
Audio
Under Output device you choose where the sound comes out, for example over HDMI on a TV with speakers. The Volume slider sets the volume; the speaker icon mutes the sound.
Brightness
The Brightness slider changes the screen brightness. Many external screens and TVs don't support this. In that case you see Brightness control unavailable; use the buttons on the screen instead.
Date & time
The top of the page shows the Controller's current time and date. With Automatic (NTP) the Controller keeps its clock in sync over the internet. Under Timezone you search for and choose your time zone, for example Europe/Zurich. Without internet, switch Automatic (NTP) off, set the date and time under Time and tap Set.
Screen lock
This area locks the Controller with a 6-digit PIN. All its settings are described under Screen lock.
Temperature & usage
Under Temperature you see the values for Processor, Storage (SSD) and Mainboard; below, Usage shows a graph for Processor and Memory. The values refresh every few seconds while the area is open.
Diagnostics: device details for support
The last area, Diagnostics, shows the Controller's details under Device, among them Device name, App version, Memory free, Disk free, Addresses and MAC address. Below that, Recent app log lists the latest app messages. Tap Copy report at the top to copy everything to the clipboard, for example for a support request.
Good to know
- You need the IP address shown under Connection type to use the remote control on your phone.
- If the Controller can't find the network, run the Connection test first. It shows whether the cable, Wi-Fi, the internet or only the licensing server is missing.
- Restart and shut down are not here but behind the red power button at the top right of Settings, see LemonScore Controller.